Adjustable Frame Panhard Mount - Outside 1.75 Inch
Warranty Information
Vendor warranty summary
Artec Industries Warranty
At a glance: Limited lifetime warranty against defects in material or workmanship
This is Artec Industries's warranty, not an NVMOS policy. We've summarized it in plain English to save you a search. The manufacturer's official terms always govern and can change without notice. Last reviewed on nvmos.com: October 4, 2026.
Coverage by product
| Product or component | Coverage |
|---|---|
| Artec Industries products | Limited lifetime, starting on delivery date |
| Returns of powder-coated products | Not returnable (manufacturer refund policy) |
What's covered
- Defects in material or workmanship for products bought, installed and used for their intended purpose
- Artec repairs or replaces a defective product at no charge (method at Artec's discretion)
What's not covered
- Misuse, abuse or neglect
- Improper installation
- Incorrect maintenance
How to make a Artec Industries warranty claim
- Call Artec at 855-278-3299 (Mon-Fri 9am-5pm MDT) to describe the issue
- Get an RMA number before shipping anything; packages without one are refused
Artec Industries contact: Phone: 855-278-3299 · Claim page / support
Bought it from NVMOS? Start with us.
Have your order number and a few photos of the issue ready, then call real humans at (920) 249-7744 or send us a message. We'll tell you whether the claim goes through us or straight to Artec Industries, and help it along either way.
Shop Artec Industries at NVMOS
Under Tailgate Plate - Aluminum, for Jeep Wrangler TJ/LJ 1997-2006
Coil Correction Plate for Jeep TJ Front Coil Springs (Pair)
Front and Rear Truss Package for Jeep Gladiator JT 2020+ (Free Front Axle Skid)
See all Artec Industries products, lead times and FAQs →
Disclaimer: The information on this page describes Artec Industries's own warranty policy. It is not a warranty offered by NVMOS (No Visible Means of Support LLC). Manufacturers update their terms at any time; we review these pages periodically, but the manufacturer's current official policy is the one that applies to your claim. Source: Artec Industries official warranty information. Last updated on nvmos.com: October 4, 2026. See our return policy for NVMOS's own terms.
About the brand
Artec Industries builds axle trusses, swap kits, suspension brackets and armor in North Salt Lake, Utah. NVMOS carries Artec reinforcements, control arms, skids, bumpers, fenders and battery mounts for Jeep, Toyota and Super Duty axles. It's for rigs running big tires and lockers that need housings and brackets that stay straight.
Based in: North Salt Lake, Utah · Made in: USA — most parts built in-house in Utah · Founded: 2003 · Lead time: Artec in-stock orders: 2–4 business days; NVMOS stock: 24–48 hours
Shop all 472 Artec IndustriesWarrantyAll brands
Warranty terms are set by Artec Industries, not NVMOS, and can change. Bought from us? Call (920) 249-7744 and we'll handle the claim with the brand.
The Artec Industries Adjustable Frame Panhard Mount anchors the frame end of a custom track bar on a 3-link or 4-link build. This Outside 1.75" version is sized for joints with a 1.75" mounting width — 3/4" and 7/8"x3/4" rod ends running high-misalignment spacers — and it puts three mounting positions at your disposal, dropping the bar 2", 3.25", or 4.5" below the frame so you can keep the track bar flat and matched to your drag link at ride height. Built from 1/4" boxed steel plate, it welds on as a permanent, structural frame anchor.
Features
- 1/4" boxed steel plate, CNC laser cut and bent for precise fit-up
- 1.75" outside mounting width with 9/16" bolt holes
- Fits 3/4" and 7/8"x3/4" rod ends with high-misalignment spacers
- Three mounting positions at 2", 3.25", and 4.5" of drop from the frame
- Works on any 3-link or 4-link suspension that runs a track bar
- Weld-on construction; made in the USA
Measure your rod end plus spacer stack and confirm it comes to 1.75" across before ordering, and note the install typically means removing the OEM track bar mount, prepping the frame, and welding — follow up with an alignment and re-torque the bolt after the first 50 miles. Pair it with the axle-side Adjustable Panhard Mount for Axle and finish the joint with 7/8" High Misalignment Spacers. Related hardware lives in track bar brackets and frame brackets.
Specifications
Adjustable Frame Panhard Mount FAQs
What rod ends fit the 1.75" version?
It is sized for joints with a 1.75" outside mounting width — that covers 3/4" and 7/8"x3/4" rod ends fitted with high-misalignment spacers, on a 9/16" bolt. Measure your rod end plus spacer stack and confirm it totals 1.75" across before ordering.
Is this the frame side or the axle side of the track bar?
This is the frame-side anchor. The other end of the bar lands on an axle-side mount — Artec's Adjustable Panhard Mount for Axle is the matching piece. Using adjustable mounts on both ends makes it much easier to get the bar flat and parallel to the drag link at ride height.
What does the install involve?
It welds to the frame, which typically means removing the OEM track bar mount, prepping the rail, positioning the bracket, and running structural welds. Set your axle centering and bar angle first, get an alignment afterward, and re-check the bolt after the first 50 miles.
Multi-column
Join Our Community
For all things NVMOS, check us out on Instagram and Facebook!
Financing Available
Buy now, pay later with PayPal Credit — available at checkout.
Contact Us
Have a question? Just send us an e-mail at support@nvmos.com
