Toyota Tundra Roof Racks by Generation and Cab
A Toyota Tundra roof rack turns the big cab roof into usable space for recovery boards, cases, fuel, lights or a tent. What fits comes down to your generation, your cab (most racks are CrewMax only) and whether you will drill the roof. This guide sorts the Tundra roof racks NVMOS carries by truck and lays out what each listing says about mounting, height and load ratings.
Short answer: Start with your generation and cab. For a 2007–2021 CrewMax, the main choices are KC HiLiTES Platform One, RCI Ascent or Horizon, Ruff Rax, Cali Raised LED (2014–2021) and Prinsu. For a 2022-and-newer CrewMax, look at Platform One, upTOP KILO, Backwoods DRIFTR, Ruff Rax, Cali Raised LED and Prinsu. Double Cab owners have fewer options, mainly Prinsu. Plan on drilling for almost all of them, and check the dynamic (driving) load rating, not just the parked number.
Platform rack or crossbars: what you are choosing between
There are two basic ways to put a rack on a truck roof:
- Crossbars. Two or three bars across the roof. Light and simple, good for a cargo box, bikes or a kayak, with fewer mounting points and usually no fairing.
- Platform rack. Side rails, a front fairing and several slotted crossbars covering most of the roof. More mounting points, a place for a light bar and a flat deck, but more weight and usually drilled mounting.
Nearly every Tundra-specific rack we carry is a platform. KC calls Platform One a hybrid: formed sheet-metal side rails with adjustable crossbars and a slotted upper deck. Most use T-slot extrusions, and Ruff Rax says its crossbars take Thule, Yakima, Rhino-Rack and T-slot mounts. RCI offers the same rack with aluminum T-slot crossbars (Ascent) or 12 gauge steel crossbars (Horizon). For the Prinsu range, our Prinsu roof rack guide goes deeper.
Toyota Tundra roof racks by generation
Roof racks are shaped to the cab, so nothing carries over between generations, and a CrewMax rack will not fit a Double Cab.
2000–2006 Tundra (1st gen)
Prinsu covers the first-gen truck. The Prinsu Original Roof Rack for the 2000–2006 Tundra Double Cab uses 2x1 aluminum T-slot crossbars and includes noise-reducing trim and a wind deflector. Install requires drilling the roof and setting plus nuts. The Prinsu Pro Roof Rack for the same truck uses Prinsu's newer crossbar, which the vendor describes as 44 percent stronger than a traditional 2x1 extrusion. It also requires drilling. Toyota added the Double Cab partway through the first generation, so confirm your cab and year before ordering. Prinsu also lists an Access Cab rack for 2000–2006.
2007–2021 Tundra (2nd gen)
This generation has the widest choice, almost all for the CrewMax:
- KC HiLiTES Platform One. The Platform One for 2007–2021 CrewMax has a 65 x 53 inch platform, sits a maximum of 3.75 inches above the roof and hides wire channels for future lights. It mounts with drilled, sealed Rivnut inserts, and KC rates the install as difficult. The Platform One with 360° Lighting adds a 57-inch Gravity Titan bar and Profile 10-inch SideCast side lights.
- RCI Ascent and Horizon. The RCI Ascent uses 1 x 2 inch aluminum T-slot crossbars and the RCI Horizon uses 1 x 2 inch 12 gauge steel crossbars. Both have 1/4-inch 5052 aluminum side panels and require drilling. RCI says neither is currently compatible with sunroof-equipped trucks, and on trucks with a shark fin antenna the rear fairing may need to come off.
- Ruff Rax. The Ruff Rax Modular Roof Rack for 2007–2021 is an aluminum platform with five crossbars and a 6-inch height. The listing says it rides on TP-54 roof tracks with drilling required, and it does not name a cab, so confirm yours with us.
- Cali Raised LED (2014–2021 CrewMax). The Cali Raised LED Premium Roof Rack for 2014–2021 CrewMax is listed as designed to be 100% bolt-on, with six extrusion bars and an adjustable wind deflector that covers a light bar when you are not using it. It does not list 2007–2013 trucks.
- Prinsu. Prinsu lists the Tundra CrewMax Prinsu Pro Roof Rack (2007–2021) plus a CrewMax Camper Pro, a CrewMax Cab Rack and a Double Cab rack for this generation. These listings do not spell out mounting or load ratings, so call us to confirm before you order.
2022 and newer Tundra (3rd gen)
- upTOP KILO. The upTOP KILO for 2022–2026 CrewMax is an aluminum rack that upTOP says sits just above the shark fin antenna, adds roughly 3/8 inch of height and works with the factory sunroof. upTOP notes that unlike some KILO fitments, the Tundra version requires drilling.
- Backwoods DRIFTR. The DRIFTR Toyota Tundra Roof Rack (2022–2026) for the CrewMax is 1/4-inch aluminum, 53.75 x 70 inches and 60 lb, and sits 0.75 inch above the antenna. It installs with rivets, and the rivet tool, drill bit and stop collar come in the kit. The front fairing has cutouts for up to a 50-inch light bar.
- KC HiLiTES Platform One. The Platform One for 2022–2026 CrewMax has the same 3.75-inch maximum deck height and drilled Rivnut mounting as the 2nd gen version. The 360° Lighting version is titled 2022–2026, but KC's description lists 2024–2026 CrewMax, so confirm your year with us.
- Ruff Rax, Cali Raised LED and Prinsu. The Ruff Rax rack for 2022-and-newer Tundras has flush crossbars that Ruff Rax says cut wind noise, and lists drilling as the mounting interface. The Cali Raised LED Premium Roof Rack for 2022+ CrewMax is a drill-in rack. Prinsu lists CrewMax, Pro and Double Cab roof racks for 2022–2025, and the Double Cab rack is one of the few 3rd gen options for that cab.
Running a fiberglass topper instead? The Prinsu Top Rack for Truck Toppers bolts to toppers with Thule or Yakima tracks, with no drilling on the truck, and capacity is limited by the topper. Bed racks are another way to carry gear, and some, like the Backwoods DRIFTR topper, line up level with the roof rack.
Drilling, profile and load ratings at a glance
What each listing says. Where a listing is silent, we say so.
| Rack | Fits (as listed) | Mounting | Height | Load rating (as listed) |
|---|---|---|---|---|
| KC HiLiTES Platform One | 2007–2021 or 2022–2026 CrewMax | Drill, sealed Rivnuts | 3.75 in max above roof | KC says the vehicle roof limit governs |
| upTOP KILO | 2022–2026 CrewMax | Drill | About 3/8 in above shark fin | 250 lb driving, 850 lb parked |
| Backwoods DRIFTR | 2022–2026 CrewMax | Rivets (tool and bit included) | 0.75 in above antenna | 300 lb dynamic, 700 lb static |
| RCI Ascent / Horizon | 2007–2021 CrewMax, no sunroof | Drill | Not listed | Not listed |
| Ruff Rax | 2007–2021 or 2022+, cab not stated | Drill, roof tracks | 6 in | Listed figures look reversed; call us |
| Cali Raised LED Premium | 2014–2021 or 2022+ CrewMax | Listed as bolt-on (2014–2021), drill-in (2022+) | Not listed | Not listed |
| Prinsu Original (1st gen) | 2000–2006 Double Cab | Drill, plus nuts | Not listed | Prinsu says most of its racks: 400 lb dynamic, 800 lb static |
| Prinsu Top Rack | 2022–2026 with tracked topper | Bolts to topper tracks | Not listed | Limited by the topper |
Dynamic vs static. Dynamic is the load while driving, when bumps, braking and wind multiply the forces. Static is the load while parked, which is why it is higher and why it matters for a tent with people in it. Eezi-Awn's K9 listing for the 2nd gen Tundra says up to 1,000 lb static and around 500 lb dynamic are possible. A rack rating does not raise your truck's roof limit, so check your owner's manual, and count the rack's own weight against the dynamic number. If you plan to run a rooftop tent, the tent plus the rack has to fit the dynamic rating.
Low profile. The lowest racks here sit within an inch of the antenna. Low racks help with garages. On a lifted truck, measure total height with gear before you try a parking garage. See our Tundra lift kit guide for lift heights.
Drilling vs no-drill, wind noise and installation
Most racks here do not use factory mounting points; they attach with Rivnuts, plus nuts or rivets set into holes you drill in the roof. Done right and sealed, they are permanent and solid, but you are cutting holes in the cab. KC and Ruff Rax both point to professional installation, and upTOP says to have a shop do it if you are not comfortable drilling. Measure carefully and seal every hole to avoid leaks.
If you do not want holes, your options are narrower. Cali Raised LED says its Premium rack for 2014–2021 CrewMax trucks is designed to be 100% bolt-on with no major modifications, so ask us to confirm before counting on a no-drill install. A tracked topper can carry the Prinsu Top Rack instead.
Wind noise. Any rack can add some highway noise. Fairings, flush crossbars and rubber trim help, and an exposed light bar or empty crossbar can whistle. upTOP points to its adaptive windscreen, Ruff Rax to flush crossbars (noise strip sold separately), Cali Raised LED to its fitted profile and Prinsu to the trim and deflector on its Original rack. Treat these as vendor claims and expect some noise with gear on top.
Mounting lights and gear
A roof rack is often where a Tundra build gets its lights. A few rack-specific options:
- Front light bar. The Baja Designs 7XL Linkable Roof Light Bar Kit for Prinsu Rack fits 2007–2021 Tundras with a Prinsu rack that has the 40-inch cutout. The DRIFTR fairing takes up to a 50-inch bar, and KC builds its lit Platform One kits around a 57-inch bar.
- Cali Raised LED lighting kits. The Premium Roof Rack Lighting Kit for Tundra includes brackets, a harness and a year-matched switch (tall style for 2007–2013, small for 2014–2021, square for 2022 and newer).
- Recovery boards and gear. The Cali Raised LED Roof Rack Traction Board Mount is steel and fits most racks with aluminum extrusion crossbars. For straps and anchor points, see our guide on why roof rack tie-down anchors matter.
Roof lights are usually meant for off-road use only, and the rules on covering or using them on public roads vary by state, so check yours.
For the rest of the truck, see our Toyota Tundra overland build guide and the Tundra accessories guide.
What NVMOS carries
Our Tundra roof racks come from KC HiLiTES, upTOP Overland, Backwoods Adventure Mods, RCI Metalworks, Ruff Rax, Cali Raised LED and Prinsu Design Studio. A few to start with:
2000–2006 Tundra
- Prinsu Design Studio Original Roof Rack, Toyota Tundra Double Cab 2000–2006
- Prinsu Design Studio Pro Roof Rack, Toyota Tundra Double Cab 2000–2006
2007–2021 Tundra
- KC HiLiTES Platform One Roof Rack for 2007–2021 Toyota Tundra
- KC HiLiTES Platform One Roof Rack with 360° Lighting for 2007–2021 Toyota Tundra
- RCI Ascent Roof Rack, 2007–2021 Toyota Tundra CrewMax
- RCI Horizon Roof Rack, 2007–2021 Toyota Tundra CrewMax
- Ruff Rax Modular Roof Rack for Toyota Tundra (2007–2021)
- Cali Raised LED Premium Roof Rack for 2014–2021 Tundra CrewMax
- Toyota Tundra CrewMax Prinsu Pro Roof Rack, 2007–2021
2022 and newer Tundra
- upTOP KILO Roof Rack for Toyota Tundra CrewMax, 2022–2026
- DRIFTR Toyota Tundra Roof Rack (2022–2026)
- KC HiLiTES Platform One Roof Rack for 2022–2026 Toyota Tundra
- Ruff Rax Modular Roof Rack for Toyota Tundra (2022 and newer)
- Toyota Tundra Double Cab Roof Rack, 2022–2025 (Prinsu)
- Prinsu Design Studio Top Rack for Truck Toppers, Toyota Tundra 2022–2026
Browse by category: Complete Roof Racks, Roof Rack Accessories, Rack Mounts and Brackets, Light Bar Mounts, Prinsu Pro Roof Racks and Toyota Tundra. You can also shop by vehicle, check current lead times (many racks are built to order) and read our vendor warranty policies.
Frequently asked questions
Do I have to drill my Tundra's roof to install a roof rack?
For most racks, yes. KC HiLiTES Platform One, upTOP KILO, RCI Ascent and Horizon, Ruff Rax, the Backwoods DRIFTR and the 1st gen Prinsu racks are all listed as needing drilling, rivets or Rivnuts. Cali Raised LED lists its Premium rack for 2014–2021 CrewMax trucks as designed to be 100% bolt-on; confirm with us. If you run a fiberglass topper with Thule or Yakima tracks, the Prinsu Top Rack bolts to the topper with no drilling on the truck.
What is the difference between dynamic and static load rating?
Dynamic is the load while moving. Static is the load while parked. Backwoods rates the DRIFTR at 300 lb dynamic and 700 lb static, and upTOP rates the KILO at 250 lb while driving and 850 lb parked. Your truck's own roof load limit still applies while driving.
Will a 2007–2021 Tundra roof rack fit a 2022 or newer Tundra?
No. The 2022-and-newer cab is a different shape, and every rack we carry is listed for one generation.
Do these racks fit a Double Cab Tundra?
Most do not. Nearly every Tundra rack we carry is listed for the CrewMax. For Double Cab trucks we list Prinsu racks for 2000–2006, 2007–2021 and 2022–2025. The Ruff Rax listings do not name a cab, so ask us. Check the cab named in the product title before you order.
Will a roof rack cause wind noise on my Tundra?
It can. How much depends on the rack, the fairing and what you carry. Front deflectors, flush crossbars and noise trim tend to help.
Can I use a roof rack with a sunroof?
It depends on the rack. upTOP says the KILO works with the factory sunroof on the 2022-and-newer CrewMax. RCI says its Ascent and Horizon racks for 2007–2021 CrewMax trucks are not currently compatible with sunroof-equipped models.
Can I mount a light bar on a Tundra roof rack?
Yes, on most of them. The DRIFTR front fairing has cutouts for up to a 50-inch bar, KC sells Platform One with a 57-inch Gravity Titan bar, and the 1st gen Prinsu racks offer a 40-inch light bar cutout. upTOP says single-row bars up to 40 inches on the KILO need its Universal Light Bar Mounting Kit. Check your state's rules on using roof lights on the road.
Not sure what fits your truck? Call a real person at (920) 249-7744 or send us a message, and we will help you sort it out.






