How to Haul Dirt Bikes in a Truck Bed (No Trailer)
You can haul a dirt bike in your truck bed and leave the trailer at home: one vehicle, one parking spot, nothing to hitch up. This guide covers carrying options, what holds the bike in the bed, loading, what fits, short beds and tailgates, and the straps and checks that keep the bike where you put it.
Short answer: To haul a dirt bike in a truck bed without a trailer, load it with a ramp or two people, seat the front wheel in a chock or mount, and strap the bars down to solid anchors on both sides. If you need the bed for other cargo, a hitch-mounted carrier puts the bike behind the truck instead.
Why haul in the bed instead of towing a trailer
For a big group a trailer still makes sense. For one to three bikes, the bed of the truck you already drive does the job with fewer moving parts.
- Nothing to store or maintain. No trailer tires, bearings or lights, and no separate registration (rules vary by state; check yours).
- Easier parking. A truck alone fits a normal spot at the gas station or trailhead.
- The hitch stays free. You can still pull a camper or a utility trailer with the bikes riding in the bed.
- The trade-offs. Bikes use bed space, count against your payload rating (the sticker in the driver door jamb) and make the truck taller, so watch garage doors.
Three ways to carry a dirt bike in a truck bed
| Method | How the bike rides | Bed space left | Good fit for |
|---|---|---|---|
| Wheel chock and straps | Upright on the bed floor, front wheel in a chock against the front of the bed | Most of the floor is taken by the bike | An occasional single-bike trip |
| Hitch-mounted carrier | Behind the truck on the receiver | The whole bed stays open | Riders who need the bed for other cargo; check your hitch's tongue weight rating |
| Rack with moto mounts | Upright in mounts on a rack that spans the bed | The floor under the rack stays open for gear | Regular riding, two or three bikes, or mixed bike and moto loads |
If a hitch carrier suits you better, we carry MotoTote motorcycle hitch carriers, and our hitch motorcycle carrier guide covers sizing and hitch ratings. The rest of this guide covers hauling in the bed.
What holds the bike in the bed
Whatever carries the bike, the job is the same: keep the front wheel from moving side to side, and give the straps solid points to pull against.
- A wheel chock. A chock at the front of the bed cradles the front tire so the bike stays upright while you strap it. On a Tacoma, the Fishbone Offroad Wheel Chock System is 10-gauge steel and adds tie-in points for dirt bikes.
- Anchors that hold. Straps are only as good as what they hook to. Charvonia Design makes bed and rail tie-down anchors for most of the trucks we support.
- A rack over the bed. A chase rack or bed rack spans the bed and keeps the floor clear underneath. Browse chase racks and bed racks for your truck, and confirm a rack is rated for bikes before you plan a load around it.
If you are planning the rest of the bed around a rack, our truck bed storage and organization guide covers rails, panels and tie-down options.
Loading: two people or one person and a ramp
Getting the bike up to bed height is the hardest part of hauling without a trailer. Park on level ground, set the parking brake and drop the tailgate before you start.
Two-person lift
Two people is the easy way. One handles the bars and front brake while the other lifts the rear into the bed.
Solo with a ramp
For riders who load alone, a ramp does the lifting. Pick one rated for more than your bike weighs and make sure it locks to the tailgate or bed so it can't kick out.
Walk the bike up beside the ramp with a hand on the front brake. Once the front wheel is seated, hold the bike upright and get the first strap on before you let go.
What fits: weight and bed length
Two numbers matter. The first is payload: add up the bikes, any rack, fuel, gear and passengers, and compare the total with the payload on your door-jamb sticker. The second is room: measure the bed with the tailgate closed and compare it with the bike's overall length.
A rack, chock or ramp listing will give its own weight rating. Use the lowest rating in the setup, not the highest.
Short beds and closing the tailgate
Short beds are where a dirt bike gets tight. Angling the bike, with the front wheel toward a front corner, often buys enough room. If the tailgate still won't close, haul with it down and make sure the straps, not the tailgate, are holding the bike.
Carrying two or three bikes side by side, stagger them front to back so the handlebars clear each other, and watch that no bar or lever is resting on the bike next to it.
Straps and pre-trip checks
For the straps themselves, use soft loops on the bike and rated tie-downs to solid anchors. The MotoTote SafeLoop Ratcheting Tie Downs are locking soft-loop tie-downs with a 1,130 lb working load limit, and the MotoTote HandleCuff Ratcheting Tie Downs cuff onto handlebar grips up to 32" with a 1,390 lb working load limit.
How to strap a dirt bike
- Soft loops on the bike. Wrap the bars close to the triple clamp or the lower triple clamp itself, clear of cables, levers and hoses.
- Pull down and out. Run one strap to each side so they pull against each other and keep the bike centered.
- Compress, don't bottom. Snug the straps until the fork is partly compressed, not bottomed out.
- Tie off the tails. Loose ends flap and wear through.
- Add a rear strap for rough roads. It keeps the back end from walking.
Bed anchors versus rail anchors is its own decision; our guide to bed tie-downs vs rail tie-downs walks through both.
Pre-trip checklist
- Re-check tension. After the first few miles and at every fuel stop.
- Fuel off. If the bike has a fuel petcock, close it for the drive.
- Brake light visible. A loaded bed or rack can hide the cab-mounted third brake light. Have someone check it from behind before you leave.
- Lock it at stops. Run a cable lock through the frame and around a solid anchor.
What NVMOS carries
For hauling bikes, these are the pieces we carry:
- MotoTote motorcycle hitch carriers
- Fishbone Offroad Wheel Chock System (Tacoma)
- MotoTote SafeLoop Ratcheting Tie Downs
- MotoTote HandleCuff Ratcheting Tie Downs
- MotoTote Universal Tie Down Bundle
- Charvonia Design bed and rail tie-down anchors
- Chase racks and bed racks
Browse by category: Chase Racks, Bed Racks, Bed Accessories and MotoTote hitch carriers. You can also shop by vehicle, check current lead times, or read our vendor warranty policies.
Shop MotoTote Hitch Carriers →
Frequently asked questions
Can you haul a dirt bike in a short bed truck?
Usually, yes. Chock the front wheel, angle the bike toward a front corner if you need the room, and strap it to solid anchors. If the tailgate won't close, haul with it down and let the straps do the holding.
How do you load a dirt bike into a truck bed by yourself?
Use a ramp rated for more than the bike weighs, park on level ground, and walk the bike up beside the ramp with a hand on the front brake. Get the first strap on before you let go. Without a ramp, use two people.
How many dirt bikes fit in a truck bed?
It depends on bed width, handlebar width and how the bikes are mounted. Stagger them front to back so the bars clear each other, and keep the total under your payload rating.
Can I close the tailgate with a dirt bike in the bed?
Often, yes, if the bed is long enough for the bike. On shorter beds, angling the bike can help. If it still won't close, haul with the tailgate down and make sure the straps, not the tailgate, hold the bike.
What straps should I use to tie down a dirt bike?
Use soft loops on the bike and rated tie-downs to solid anchors. The MotoTote SafeLoop Ratcheting Tie Downs are locking soft-loop tie-downs with a 1,130 lb working load limit.
Do I have to drill my truck bed to install a rack?
Not always. Some racks clamp to the bed rails and others bolt on. Check the install notes on the listing for your rack and truck.
Can I haul an e-moto the same way?
Yes. Strap an e-moto the same way as a dirt bike, and include its weight in your payload math.
Not sure how many bikes your bed can take? Call a real person at (920) 249-7744 or send us a message, and we will help you sort it out.






